INSTRUCTION MANUALPART NO. 426-02-651-0055 - 08-26-05 - Rev. A Copyright © 2005 Delta MachineryTo learn more about DELTA MACHINERY visit our website a
10ATTACHING THE MOTOR TO THE MOTOR BRACKET1. Position the motor (A) Fig. 5 on the motor brackets (B). Align the holes in the motor with the holes in
11SINGLE PHASE (MODELS 28-248F & 28-348F) & THREE PHASE (MODELS 28-248G & 28-248G)NOTE: The single phase LVC box comes with a connected po
12INSTALLING THE DUST CHUTE1. Insert the dust chute through the door opening into the slot (A) Fig. 8 in the top of the stand. NOTE: Place the motor
13ATTACHING THE DOOR TO THE STAND1. Align the two holes in one of the male hinges (A) Fig. 14 with the two holes on the stand. NOTE: Point the hinge
14ATTACHING THE SAW TO THE STANDThe band saw is VERY heavy. Use a helper to attach the saw to the stand.1. Position the band saw on top of the stand
15ATTACHING THE TABLE TO THE SAW1. Insert the two table studs (A) Fig. 24 on the bottom of the table into the two holes in the trunnion assemblies (B
16ATTACHING THE BLADE TO THE SAWUse only 93-1/2" blades on the 14" band saw.1. Remove the table pin (A) Fig. 28.2. Open the blade guard do
17ATTACHING THE ON / OFF SWITCH TO THE STAND1. Remove the two outer hex nuts and lock washers (A) Fig. 31 from the two screws on the back of the swit
18OPERATIONSTARTING AND STOPPING THE SAW1. The on/off switch is located on the left side of the machine. To turn the machine “ON”, push the green st
19ADJUSTING THE 90° DEGREE TABLE STOP1. Loosen the table clamp handles (A) Fig. 40, and tilt the table to the right.2. Rotate the stop (B) Fig. 42 o
2Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precauti
20When cutting thin pieces (3/4" or less), set the blade tension below the maximum setting for blade width to extend the life of the blade.Over-s
21Before tracking the blade, make sure that the blade guides and blade support bearings are clear of the blade.TRACKING THE BLADEAfter applying tensio
22Adjust the upper blade guides and blade support bearings ONLY AFTER the blade has the correct tension and is tracking properly. To adjust:1. Make s
23CUTTING CURVESWhen cutting curves, turn the stock carefully so that the blade follows without twisting. If a curve is so abrupt that it is necessary
24Trouble: BAND SAW DOES NOT COME UP TO SPEED.Probable Cause Remedy 1. Low voltage due to improper extension cord size. 1. Replace with adequate
25BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw blade i
26REPLACEMENT PARTSWhen servicing use only identical replacement parts. Check the parts list included for more information. Parts lists can also be fo
Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine a
28 Delta Machinery 4825 Highway 45 NorthJackson, TN 38305www.deltamachinery.com
3It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. Th
4GENERAL SAFETY RULESREAD AND UN DER STAND ALL WARNINGS AND OP ER AT ING IN STRUC TIONS BE FORE USING THIS EQUIP MENT. Failure to follow all instructi
5ADDITIONAL SPECIFIC SAFETY RULES1. DO NOT OPERATE THIS MACHINE UNTIL it is assembled and installed according to the instructions.2. OBTAIN ADVIC
6Fig. A Fig. BGROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESGROUNDED OUTLET BOXGROUNDING MEANSADAPTERPOWER CONNECTI
73. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive: If the machin
812345UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all u
924. Table Handle (2)25. Male Hinge (2)26. Door Latch27. Female Hinge (2)28. Cord Bushing151617181920212223242526272815. 5/16-18 x 1-1/2" Hex Hea
Kommentare zu diesen Handbüchern